A few tricks for automotive hail damage repair projects? 1st let’s start with some car paint care recommendations: Repair times are up to the severity of the hailstorm and the damage on your car. For the light or moderate damages, the repairs may take from 1 to 3 days. But for heavy damages, it may take you 2 to 3 weeks as that damages will needs body shop participation, for paint work and panel replacement.
This technique is popular among automotive enthusiasts when it comes to the removal of small dents. The idea is simple: heat will inevitably cause the metal surface to expand and (hopefully) pop the dent out. Remember that the more time the car spends time under the sun, the better this technique will work. Use a plastic and/or leather conditioner for the car’s interior, so as to not damage it while exposing the car to maximum sunlight. If the sun’s heat isn’t particularly strong that day, a simple hair dryer could be used in conjunction with the sun to concentrate the heat to a specific area. Point the hair dryer to the dented area for two-minute intervals until the dent pops out. Be careful not to touch the hot lip of the hair dryer on any painted surface. A two-to-four inch gap between the dryer and the surface is recommended.
Apply the dry ice as many times as you need to, but it should pop out eventually if the dent isn’t too deep. You can also try heating up the dent first, with something like a hair dryer (similar to the hairdryer and compressed air tip above), and then apply the dry ice to it. Suction is one way to get out a dent, but the problem is finding a dent puller with the right amount of power. Well, why not just create your own? All you need is a pot (or bucket), a vacuum cleaner and some tape and you can get that dent out of your car in no time.
I don’t care if you wash your car yourself (more on that strategy later in this page) or you take it to a quality car wash. (Yes, not all car washes are created equal) This is not an option as dirt is your #1 enemy when it comes to the finish on your new car paint. And this doesn’t mean once every 6 months whether it needs it or not. This means regularly and consistently. (A minimum of once a month…minimum!)
So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned. Find extra info on Automotive Repair & Customization in Colorado Springs.
Clean the Car. One of the most important things you can do to maintain the exteriors of your car is to wash and shampoo the vehicle regularly. Commercial power washes are also beneficial if you use them every few months. Make sure you keep a good distance between the surface of the car and the pressure jet, so you don’t damage the paint. If you’re unsure you could get it done professionally.
The first step to performing a dent repair without using paint involves assessing the dent itself and determining if a paintless dent repair is even possible. According to most experts, 80 to 90 percent of dents can be repaired using PDR techniques. However, there are a certain percentage of dents that are impossible to repair without following it up with a paint job. The following types of dents usually fall into this “non-PDR” category: Very deep dents – Even very large dents can be repaired using PDR if the dent is fairly shallow. However, if a dent of any size is pushed in too far, the metal can’t be bent back into place without damaging the paint and requiring repainting.